CIMCO Edit 2026 Releases

CIMCO Edit 2026.01.23 PreviewReleased: 01-10-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.23
  • Fix: Roeders reverse post: SPOINT, SRAWBLOCK and other probing cycles.
  • Fix: Haas turning reverse post: tool change position, subspindle issues, added G100/101.
  • New: Rapid move tool/workpiece and hidden model collisions are now on by default.
  • Fix: MillPlus reverse post: G40.
  • Fix: Siemens milling reverse posts: G700.
  • Fix: Heidenhain reverse posts: TCPM SPAT.
  • Fix: Fanuc milling reverse post: #4130.
  • Fix: Default work offset from setup file was scaled by 25.4 in inch machines.
  • Fix: Improved file comparison performance by approximately 10-20% and increased the number of differences that can be compared before reaching the comparison limit.
  • Fix: Machine box did not follow the machine type.
  • Fix: Fagor milling reverse post: G43/44, G83.
  • New: Added 'Insert Side' to Tool Mount Properties.
  • Fix: Fagor turning reverse post: G69.
  • Fix: Double navigation bar tooltip.
  • Fix: Siemens milling reverse post: ROT, CYCLE978.
  • Fix: Reverse post: subprogram call issue.
  • New: Fanuc 0i model F milling reverse post. (S28949)
  • Fix: Fanuc turning reverse posts: G71.
  • Fix: Mazak Integrex reverse post: G12.1.
  • Fix: Haas turning reverse post: sub spindle transformation issue.
  • New: Collinear axes in the work offsets table.
  • New: Showing programmed work offsets. (S30073)
  • New: GibbsCAM keyboard/mouse mapping. (S30208)
  • Fix: Backplot crash when updating work offset rotation angles.
  • Change: Increased the maximum number of macro user input parameters from 60 to 100. (S30135)
  • New: Added an optional minimap for editor documents, configurable under Setup > General > Editor > Editor settings > 'Show minimap in editor documents'. (S29712)
  • New: Added a minimap to File Compare, enabled by default and configurable under Setup > File Compare > File compare settings > 'Show minimap'. (S29712)
  • New: Added a minimap to Multi Channel Synchronization, enabled by default and configurable under Setup > Multi Channel > Multi channel view > 'Show multi channel minimap'. (S29712)
CIMCO CNC-Calc 2026.01.23
  • Fix: Fixed issue with persisted data not always being loaded.
  • Fix: Fixed issue with post processor override text field not updating when changing machine.
CIMCO Edit 2026.01.22 PreviewReleased: 11-09-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.22
  • Fix: Reverse post: issue with Y-shifted tool mounts.
  • Fix: Fanuc milling reverse post: #4130.
  • Fix: Reverse post: wrong message output for selected code simulation in some cases.
  • New: Clickable view cube.
  • New: Grid-lines in Backplot.
  • New: Now uses empty holder instead of default when scanned tool doesn't contain a holder.
  • New: Now shows license info in presentation viewer status bar.
  • Fix: Station number scanning for custom tools.
  • Fix: Turning reverse posts: wrong tool cutter point in some cases.
  • Fix: Okuma milling reverse post: G272/282.
CIMCO Edit 2026.01.21 PreviewReleased: 08-09-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.21
  • New: Crisper rendering when windows scaling is 125%, 150% or 175%.
  • New: Better frame rate when windows scaling is 175% or above.
  • Fix: Turning reverse posts: wrong moves on sub-spindle when in inches.
  • New: Turning inserts can now be seen through the holders.
  • New: Crisper text rendering.
  • Fix: Now doesn't revolve the table for turning moves that position the spindle.
  • Fix: An issue where custom tool profiles with multiple adjacent arcs could corrupt stock simulation.
  • Fix: Custom tool from DXF when containing 180 degree arcs.
  • Fix: Measure distance edge and corner highlight would sometimes appear when not measuring.
  • Fix: Okuma reverse posts: MODIN, MODOUT.
  • Fix: Haas reverse posts: fixed DPRNT, POPEN, PCLOSE warnings.
  • Fix: Okuma turning reverse post: G20.
  • Fix: Fanuc milling reverse post: M29.
  • Fix: Mazak reverse posts: G84.2.
  • Fix: Turning reverse posts: wrong turret head moves at the first tool change.
  • Fix: Stock from DXF when DXF contains lwpolylines.
CIMCO Edit 2026.01.20 PreviewReleased: 01-09-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.20
  • New: Machines are now grouped in machine builder by 'My machines' and 'Preconfigured machines'.
  • Fix: Fanuc milling reverse post: G53.1. (S30147)
  • Fix: A crash when starting simulation reported for some users.
  • New: Measure distance now snaps to geometries, edges and corners.
  • New: Cross Section now available with only workpiece.
  • New: Cross Section can now cut through tool.
CIMCO Edit 2026.01.19 PreviewReleased: 31-08-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.19
  • Fix: Mazak reverse posts: G53.1, M107/108.
  • Fix: Editor jumps line when editing NC code.
  • Fix: An issue where cross section was off center.
  • Fix: An issue where cross section didn't always save state properly when toggling.
  • Fix: Siemens turning reverse post: TRAORI.
  • Fix: Mazak Integrex reverse post: G97R, G43.4P.
  • Fix: Fanuc milling reverse post: #999.
  • Fix: Millplus reverse post: G22, G23, G29.
  • Fix: Multiple scanned geometries using same STL but different transformations.
  • Fix: Haas reverse posts: M97, G103.
  • New: Custom lathe holder STL is now used without a profile.
  • New: Remembers work offsets in file type.
  • New: Brother milling with turning reverse post. (S28627)
  • Fix: Millplus reverse post: G74. Added home position control settings.
  • New: Show active dynamic offset.
  • Fix: Tool vs fixture collision detection in Backplot mode on lathes.
  • Fix: Y axis turning issues.
  • Fix: An issue where remove chips could remove the entire stock model.
  • New: Added Backplot, NC-assist, Multi-Channel View and Advanced Math Functions to CIMCO Edit Core.
  • New: Added collision and limit over-travel report to CIMCO Edit Pro.
  • New: Added stopping conditions to CIMCO Edit Pro.
  • New: Added collision highlight to CIMCO Edit Pro.
CIMCO Edit 2026.01.18 PreviewReleased: 19-08-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.18
  • Fix: Fixed an issue where File Type would unexpectedly change in certain scenarios. (S30015)
  • New: Manual threading moves now supported.
  • Fix: Haas milling reverse posts: #3201-3400.
CIMCO Edit 2026.01.17 PreviewReleased: 18-08-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.17
  • Fix: Fanuc turning reverse post: added "R point programming" control setting for G81-89 of G-code system A. (S28324)
  • Fix: Haas milling reverse posts: added missing variables support.
  • Fix: Okuma milling reverse post: LAA, ARC, OMIT. (S25608)
  • Fix: Heidenhain reverse posts: SYSWRITE ID230. (S28713)
  • Fix: Fixed an issue for custom machine home position.
  • Fix: Heidenhain reverse posts: AXIS SPAT.
  • Fix: Reverse post: failing during subprogram search in some cases.
  • New: Datron milling reverse post. (S27194)
  • Fix: Siemens milling reverse posts: CYCLE72. (S28552)
  • Fix: Siemens milling reverse posts: G147/148/247/248/347/348. (S28557)
  • Fix: Heidenhain milling with turning reverse post: cycle 800.
  • Fix: Fanuc milling reverse post: G31.
  • Fix: Heidenhain reverse posts: * is used as comment only at line start.
  • Fix: Heidenhain reverse posts: TOOL CALL now accepts QS variables as tool name.
  • Fix: Siemens turning reverse post: cycle800.
  • New: Hurco turning reverse post. (S29095)
  • New: Added Off Center Turret generic lathe and 45 degree table/head machine.
  • New: Fanuc milling reverse post: arc tolerance control setting.
  • Fix: Heidenhain reverse posts: cycle 251/252.
  • New: Backplot from File now shows NC code.
  • New: Backplot active selection with live updates as you change the selection.
  • Fix: Fixed regex Find/Replace replacing next match instead of highlighted match. (S29840)
  • New: Tool path statistics: min/max spindle speed.
  • New: Tool list: extraction from tool call line.
  • New: G320 measurement cycle supported in Fanuc.
  • Fix: Reverse post: "#3000=1 (MESSAGE)" shows MESSAGE text for supported reverse posts.
  • Fix: Standardized C++ API.
  • Fix: Mazak Integrex reverse post: tool change command.
  • Fix: Okuma turning reverse post: TD.
  • Fix: OSAI milling reverse post: h. (S29796)
  • Fix: Haas reverse posts: now outputs error message when compensation input starts with an arc.
  • Fix: MillPlus reverse post: G43, G779, G781-789.
  • Fix: Reverse post: tool compensation for milling tools in mill-turn mode.
  • New: Custom turret slot orientations now supported.
  • New: Siemens ONE milling reverse post. (S24625)
  • Fix: An issue where machine builder preview didn't work when a Backplot window was open.
  • New: EControl milling reverse post.
  • Fix: Centroid milling reverse post: G43.3. (S28768)
  • Fix: Fixed an issue with syntax highlight coloring when switching between File Types. (S29792)
CIMCO CNC-Calc 2026.01.17
  • New: Option to select active post processor from bottom panel.
  • New: Enabled coordinate system axis indicators for milling. (S28930)
  • Removed: Disabled persistence for CAD function input.
  • Change: Unit scale rendering (lower right corner) changed to fixed size.
  • Change: Improved visibility for some cursors.
  • Fix: Active mouse interaction stopping when mouse leaves CAD view.
  • Fix: Dynamic layout in side panel not resizing buttons properly.
  • Fix: Artifacts in side panel when element info field are hidden.
  • Fix: Helix Milling 'Start at center' being ignored when lead in/out disabled. (S17940)
  • Change: Helix Milling cut transitioning.
  • Fix: Non-ANSI characters in file paths preventing opening files.
  • Fix: Zooming in/out scaling factors.
  • Change: Consistent window selection (zoom/selection).
CIMCO Edit 2026.01.16 PreviewReleased: 16-07-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.16
  • Fix: Fanuc milling reverse post: #517/518 are handled as common variables.
  • New: Matsuura milling reverse post: Fanuc based.
  • Fix: Fagor milling reverse post: #MCS.
CIMCO Edit 2026.01.15 PreviewReleased: 15-07-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.15
  • Fix: Error when saving MacBundle.
  • Fix: bug with not loading encrypted machines.
  • Fix: Siemens reverse posts: CTRANS. (S29639)
  • Fix: Siemens turning reverse post: CYCLE800.
  • Fix: Fanuc milling reverse post: G10L12R.
  • Fix: Heidenhain milling with turning reverse post: wrong retracts.
  • Fix: Siemens milling reverse post: G75.
  • Fix: Siemens turning reverse post: W collinear axis.
  • Fix: Tool manager: High feed mill tool shape.
  • Fix: Mazak Integrex reverse post: M153/154.
  • Fix: Fanuc reverse post: issue with undefined subprogram arguments.
  • Fix: Siemens reverse post: external subprogram call by file name.
  • Fix: Okuma turning reverse post: TD, M323, G126/127, G136.
  • Fix: Siemens reverse posts: supported $AA_IM[] variables.
CIMCO Edit 2026.01.14 PreviewReleased: 02-07-26
Changes since previous version:
CIMCO Edit 2026.01.14
  • Fix: Siemens reverse posts: max tool number is changed to 99999999.
  • Fix: Mitsubishi turning reverse post: spindle speed S1/2/3, tool correction G0 T*.
  • Fix: Fanuc milling reverse post: #0 variable comparison.
  • Fix: Fanuc milling reverse post: G10L12.
  • Fix: Centroid milling reverse post: G43.3, G0 interpolation. (S28768)
  • Fix: Reverse post: work offset system variables assignment issue.
  • Fix: MillPlus milling reverse post: G7.
  • Fix: Siemens milling reverse post: CYCLE840.
  • Fix: Reverse post: tool vector producing incorrect rotation in some cases. (S29496)
  • Fix: Siemens reverse posts: M7/8/9. (S29430)
  • Fix: Siemens reverse posts: supported rounding (RND) of arc-line and arc-arc corners. (S28559)
  • Fix: Haas reverse posts: supported work offset system variables #7001-#7386, #14001-#15966.
CIMCO Edit 2026.01.13 PreviewReleased: 23-06-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.13
  • Fix: Mitsubishi reverse posts: spindle commands S1/2/3.
  • Fix: Siemens reverse posts: _TC_A1/2 variables. (S29462)
  • Fix: Tool color not working when setup file scanning was disabled.
  • Fix: Slow solid removal animation in some cases when rewinding.
  • Fix: X or Y axis cylinder stock sometimes initially disappearing.
  • Fix: Heidenhain TNC7 reverse post: TCPM error message.
  • Fix: Coolant state output. (S29430)
  • Fix: Reverse post: rotation time calculation.
  • New: Thermwood Milling reverse post. (S26367)
  • Fix: Siemens reverse posts: calling subprograms starting with %_N__SPF. (S28394)
  • Fix: Fanuc milling reverse post: G53.1.
  • New: Okuma milling reverse post: G469. (S28132)
CIMCO Edit 2026.01.12 PreviewReleased: 17-06-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.12
  • Fix: Fixed an issue where automatic sync alignment in Multi Channel view could leave the cursor on the wrong line after editing synchronized NC files.
  • New: Added optional synchronization command mapping for matching different command numbers, such as M770 and M775, in multi-channel synchronization.
  • Change: "Ignore block skip" is moved from control settings to simulation settings.
  • Fix: Reverse post: G65P9811.
  • Fix: Okuma reverse posts: MSG.
  • Fix: Reverse post: inverse time feedrate (G93). (S28811)
  • Fix: Reverse post: lathe tool center compensation for tilt. (S28433)
  • New: Faster machine model / stock collision detection when the machine is frequently in close proximity.
  • New: More robust stock from STL when the STL contains internal geometry.
  • Fix: More robust machine model / stock collision detection.
  • Fix: A turning issue on some milling machines.
  • Fix: Fagor reverse post: "I" suffix support for move parameters.
  • Fix: Fixed an issue where multiline replace could miss occurrences within the current selection.
  • Fix: Fixed an issue where multiline replace would replace beyond the current selection.
  • Fix: Scanning supports tool location values for custom tools.
  • Fix: Siemens reverse posts: CYCLE800.
  • Fix: Roeders milling reverse post: supported Heidenhain commands/cycles. (S29321)
  • New: Tool manager: added tool station number to "Advanced tool location" in turning/mill-turn mode. (S29248)
  • Fix: Heidenhain millturn reverse post: cycle 800. (S28427)
  • Fix: Siemens milling reverse post: CYCLE977.
  • Fix: Reverse post: lathe threading when simulating on milling machine.
  • Fix: Fanuc turning reverse post: G76.
  • New: Okuma turning reverse post: B-axis support. (S28045)
  • Fix: Heidenhain reverse posts: APPR LEN.
  • New: Heidenhain TNC7 milling reverse post. (S24521)
  • Fix: Mitsubishi turning reverse post: G74.
  • Fix: Siemens milling reverse post: POCKET3/4.
  • Fix: MacBundle issues when using custom configuration paths.
CIMCO Edit 2026.01.11 PreviewReleased: 03-06-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.11
  • Fix: Better robustness on Intel Integrated Graphics.
  • Fix: An issue where turret mounts would not load.
  • Fix: Reverse post: spindle axis center issue in machine coordinates.
  • Fix: Heidenhain reverse posts: wrong rotation axis movements in some cases.
  • New: Reverse post: parametrized machine subprogram macros. (S29004)
  • New: Improved stock compare performance.
  • Fix: True vision rendering stale image during animation playback.
  • Fix: Sharpened shaft/shoulder stock collision margins.
  • New: Support updated web license.
  • Fix: Siemens reverse posts: $P_ACTFRAME. (S27059)
  • Fix: Siemens reverse posts: $P_UIFR.
  • Fix: Fanuc milling reverse post: rotated work offsets G10, G30.
  • Fix: Save Setup not commenting Version Number when writing to top of NC file.
  • Fix: Fanuc/Mazak milling reverse posts: G68.4.
  • Fix: Fanuc milling reverse post: G82 dwell time.
  • Fix: Mazak and Fanuc milling reverse posts: system variables #7001-7941.
  • New: Support threading tools with low corner radius and point corners.
  • Fix: Siemens milling reverse post: G_BACK_TUNNEL.
CIMCO Edit 2026.01.10 PreviewReleased: 27-05-26
Changes since previous version:
CIMCO Edit 2026.01.10
  • Fix: Fanuc milling reverse post: G68.4.
CIMCO Edit 2026.01.09 PreviewReleased: 26-05-26
Changes since previous version:
CIMCO Edit 2026.01.09
  • Fix: An issue where default tool colors would be black instead of following color loop.
  • Fix: Reverse post: wrong incremental move after angular move in turning.
  • Fix: Reverse post: repeating macro program calls in some cases.
  • New: Remembers stock compare gradient setting.
  • New: Remembers True Vision.
  • New: Added simulation shortcut for going to end (Ctrl + Shift + Space).
  • New: Added simulation shortcut for playing / pausing (Ctrl + Shift + R).
  • Fix: Reverse post: inverse kinematics issue when using spindle axis.
  • Fix: Heidenhain reverse posts: issue with ignoring some cycle parameters in some cases.
  • Fix: Consistent milling tool orientation in milling and mill-turn environment. (S28130)
  • Fix: Siemens milling reverse post: POCKET2.
CIMCO Edit 2026.01.08 PreviewReleased: 19-05-26
Changes since previous version:
CIMCO Edit 2026.01.08
  • Fix: Okuma reverse posts: OO88.
  • Fix: Fanuc reverse posts: G50.1, G51.1.
  • Fix: Reverse post: wrong entity by line number in some cases when using external subprograms.
  • Fix: A circumstantial freeze when closing Backplot.
  • New: Tweaked cursor when resizing sub program HUD.
  • Fix: Corrupt sub program HUD when Editing main program.
  • Fix: Visibility state not being remembered when toggling geometries from ribbon bar.
  • New: Reverse post: manual tool change position. (S28846)
  • Fix: Siemens reverse posts: added R1000-R1299 variables.
  • Fix: Reverse post: angular move issue in turning.
  • Fix: Siemens reverse posts: MSG command not outputs message into simulation window. (S28577)
  • Fix: Crash in remove chips.
  • Fix: Collision detection not refreshing after changing tool/workpiece setting.
  • Fix: Stock simulation when turning on an AC 5 axis milling machine.
  • Fix: Centroid reverse posts: conditional expressions. (S26828)
  • Fix: NC line highlight sometimes on wrong line when jumping to tool changes.
  • Fix: Siemens milling reverse post: CYCLE800 retract position.
CIMCO Edit 2026.01.07 PreviewReleased: 06-05-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.07
  • Fix: Centroid milling RPost: M25.
  • Fix: Siemens turning reverse post: SUPA, G53.
  • Fix: An issue where stopping conditions could would rewind/stop at before the initial play position.
  • Fix: Presentation viewer initially highlighting line 1.
  • Fix: Collision detection progress bar sometimes appearing when it shouldn't.
  • Fix: Centroid reverse posts: added #29000-31999 variables.
  • Fix: An issue where changing theme corrupted stock compare colors.
  • New: Millplus milling reverse post. (S23277)
  • New: New real-time based simulation animation speed slider.
  • Fix: Tool manager: Thread mill shape.
  • Fix: Reverse post: wrong tool rotation angles in some cases.
  • Fix: Reverse post: crash in radius compensation in some cases.
  • Fix: Black screenshot in simulation bundles.
  • New: Added gage point to custom lathe holders.
  • Fix: Fagor reverse posts: #MCS ON/OFF.
  • Fix: Heidenhain reverse posts: CYCL DEF 19.
  • Fix: Fanuc milling reverse post: system variables #2000-2399, #10001-10999, #11001-#11999, #13001-13999.
  • Fix: Arc interpolation regression.
  • Fix: Stock removal when turning with C180.
  • Fix: Fanuc turning reverse posts: #3000.
  • Fix: Fanuc turning reverse post: linear angle issue.
CIMCO Edit 2026.01.06 PreviewReleased: 29-04-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.06
  • Fix: Reverse post: macro programs issue.
  • Fix: Fanuc turning reverse post: drilling cycle R parameter is absolute/incremental depending on G90/G91 activated. (S28324)
  • Fix: Mazak milling reverse post: Tool length compensation activation control setting. (S28398)
  • Fix: An issue where special characters in tool comments and files names were sometimes corrupted.
  • New: Added turning sample file demonstrating stock flip and split stock.
CIMCO Edit 2026.01.05 PreviewReleased: 27-04-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.05
  • Fix: Mazak SmoothAi reverse posts: M98H.
  • Fix: Siemens milling reverse post: OFFN.
  • Fix: Fanuc turning reverse posts: missing variables.
  • Fix: Reverse post: radius compensation issue in mill-turn.
  • Fix: Heidenhain reverse posts: PLANE RESET STAY.
CIMCO Edit 2026.01.04 PreviewReleased: 23-04-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.04
  • Fix: Reverse post: spiral and conical arcs issue.
  • Fix: Mazak reverse posts: #3020 variable.
  • Fix: Fanuc turning reverse post: G73.
  • Fix: Fanuc milling reverse post: WCS Expansion option.
  • Fix: Legacy APT reverse post: MULTAX.
  • New: Collision detection between machine models and in-process stock.
  • Fix: Heidenhain reverse post: PLANE RESET TURN.
  • Fix: Siemens reverse posts: $P_TOOLL.
  • Fix: Heidenhain reverse posts: cycle 17.0 feed rate issue.
CIMCO Edit 2026.01.03 PreviewReleased: 16-04-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.03
  • Fix: Fixed unlocalized file type template names in 'Add new file type' dialog. (S28405)
  • Fix: Fanuc Turning STARGB reverse post extension: G910, G69.1.
  • Fix: Missing control settings localization in Haas and Mitsubishi turning reverse posts. (S28236)
  • Fix: Reverse post: G10L2P0.
  • Fix: Fanuc turning reverse posts: drilling axis issue. (S28324)
  • Fix: File open dialog for DXF shows "Open STL File"
  • Fix: Reverse post: cylindrical interpolation regression.
  • Fix: Spindle to stock collision reporting issue when the spindle model was in inches.
  • Fix: False positive stock/holder collisions when turning on stock STL.
  • New: Added Clamp/unclamp time settings.
  • New: Advanced Chuck Jaw setup.
  • Fix: Okuma milling reverse post: G283/284.
  • Fix: Siemens turning reverse post: TRANSMIT_S.
  • Fix: Siemens reverse posts: G500 fix caused regression.
  • Fix: Better simulation robustness on Intel Integrated Graphics.
  • Fix: Stock compare update when changing workpiece.
  • Fix: Collision detection issues when multiple workpieces or fixtures.
  • Fix: Issue where hiding workpiece could pause simulation.
  • Fix: Toolpath vectors only showing for half the toolpath.
  • Fix: A circumstantial freeze when closing Backplot.
  • Fix: Reverse post: diameter programming issue for variables.
  • Fix: Centroid milling reverse post: M98, M25.
  • Fix: Centroid reverse post: system variables support. (S26828)
  • Fix: Machine configuration.
  • New: Statistics can show graph for selected tools. (S27148)
  • New: Default view can now be changed in the machine configuration editor.
  • New: Now bundles external sub programs in simulation bundles.
  • New: Support vertical milling extenders.
CIMCO Edit 2026.01.02 PreviewReleased: 23-03-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.02
  • Fix: Mazak milling reverse posts: G68, G68.2.
  • Fix: Siemens reverse posts: D+SUPA command issue.
  • New: Add Keep decimals, Strip leading zeros and Strip trailing zeros options to Adjust Feedrate and Adjust Spindle Speed dialogs. (S27518)
  • Fix: Reverse post: home position units issue.
  • Fix: Stock simulation issue when C not zero.
  • Fix: arc scanning issue.
  • Fix: An issue where 'remove chips' sometimes removed the wrong piece.
  • New: Tool visibility state is now remembered.
  • Fix: Remove chips sometimes removing too much material after parting off.
  • Fix: Tool mounts missing in simulation bundles.
  • Fix: False positive collisions in turning.
  • Fix: An issue where going to end would not always update stock.
  • New: Memory optimizations.
  • New: Better STL repair for stock compare.
  • Fix: Haas milling reverse post: P9817/9818.
  • Fix: Okuma milling reverse post: VRSTT, VZOF*, fixed issue with labels.
  • Fix: Loading of stock from STL when paths contain Chinese characters.
  • Fix: Multi Channel: Fixed an issue where the configured Channel Order was not always preserved. (S28040)
  • Fix: Siemens milling reverse post: G500.
  • Fix: Mazak Integrex reverse post: M211.
  • Fix: Siemens turning reverse post: CYCLE800. (S28020)
  • Fix: Turning when work origin not on rotation axis.
  • Fix: Orientation of turning tools when turning on horizontal mills.
  • New: Automatically selects the Backplot tab when launching directly into simulation from CAM integrations.
  • Fix: Centroid milling reverse post: G43.3, G43.4 display tool position issue. (S26828)
  • Fix: Machine home position when in inches.
  • Fix: Corrupt stock when using remove chips with stock compare.
  • Fix: Reverse post: radius compensation issue.
  • Fix: NC code missing from .CimcoSimData when exporting simulation bundle.
  • New: Improved stock model collision detection.
  • Fix: Heidenhain reverse posts: M130.
CIMCO Edit 2026.01.01 PreviewReleased: 09-03-26Register to download
Changes since previous version:
CIMCO Edit 2026.01.01
  • Fix: Spindle mount collision detection.
  • Fix: Spindle mount scaling when in inches.
  • Fix: Fanuc milling reverse post: G68.
  • New: Command line (--savebundle path) for saving simulation bundle.
  • Fix: Reverse post: fixed not updating some of linked variables.
  • Fix: An issue where jumping to limit over-travel would highlight NC line 0.
  • Fix: Remove chips when on sub spindle.
  • Fix: Default mounting on cross turning tools with round shank.
  • Fix: Tool colors setting not loading correctly when starting CIMCO Edit.